BIOGAS COMPRESSORS / RNG GRID INJECTION

UVG315/ VG250

2x UVG 315  

LOCATION: SPAIN
FLUID: Biogas    
POWER INSTALLED:
 400 kW (x2)
INLET PRESSURE: 50 mbar(g)
WORKING PRESSURE: Up to 15 bar(g)
FLOW RATE: 0<1850<3700 Nm³/h
AMBIENT TEMPERATURE: -10/+40°C

VG 250

LOCATION: SPAIN
FLUID: Biomethane  
POWER INSTALLED:
 315 kW
INLET PRESSURE: 50 mbar(g)
WORKING PRESSURE: Up to 22.5 bar(g)
FLOW RATE: 0<530<1045 Nm³/h
AMBIENT TEMPERATURE: -10/+40°C

 

A complete automatic solution for biogas upgrading and biomethane grid injection consisting of:
– Two open frame screw compressors for biogas upgrading installed inside a container (40’) in Spain. Designed in compliance with the European standards for classified Atex zone 2. It is suitable for outdoor installation, water-cooled, outlet gas temperature control, fine filtration and controlled remote by PLC;
– One screw compressor for biomethane grid injection, in compliance with the Spain requirements for the biomethane grid injection. Designed for classified Atex Zone 2 for outdoor installation, water-cooled, outlet gas temperature control, fine filtration, equipped with silencers for reducing the noise level to 75 dB(A) at 1 meter and controlled remote by PLC.

[contact_form]

OTHER REFERENCES

UVG 355

Italy

Screw compressor for biogas upgrading located in Italy. Designed for outdoor installation. It is water cooled and completed with temperature control, fully electrical by-pass system, fine filtration and controlled by PLC. It is equipped with silencers for reducing the noise level to 75 dB@ 10m.
View more

UVG132/BVG30

Lithuania

Two screw compressors for biogas upgrading located in Lithuania. The first unit supplies the biogas to the upgrading system, the second recirculates the remaining methane and carbon dioxide to obtain greater efficiency for its recovery through the upgrading system. Both compressors are open frame, installed inside container, designed for classificated Atex Zone 2, equipped with with electro-pneumatic by-pass system, fine filtration, temperature control and controlled by PLC.
View more

BVG315/ADI115

France

Two compressors located in France. The first is a screw compressor for biogas upgrading. It is air-cooled and equipped with fine filtration, heat recovery, temperature control, an electro-pneumatic bypass system, and controlled by a PLC. The second is a two-stage reciprocating compressor for biomethane grid injection. It is also air-cooled and equipped with fine filtration, an electro-pneumatic bypass system, and controlled by a PLC. Both compressors are designed for classified ATEX Zone 2 for outdoor installation (-10/+40°C).
View more

BVG 30

Czech Republic

Screw biogas compressor for upgrading located in Czech Republic. Designed for classified Atex Zone 2 for outdoor installation. It is air cooled and equipped with medium filtration, bleed valve for depressurization to vent, mechanical by-pass valve and controlled by PLC. To reduce the compressed gas temperature, a chiller was provided along with the compressor.
View more

BVG132/BVG315

France

A plant with five compressors located in France. All units are screw compressors for biogas upgrading. The compressors are designed for Atex Zone 2 for outdoor installations (-20 /+40). They are air-cooled, and equipped with heat recovery, electro-pneumatic bypass system, fine filtration, temperature control and controlled by PLC. All compressors canopies are equipped with two CH4 sensors.
View more

Model BVG 45

Poland

Two screw compressors for biomethane located in Poland. Designed for classified area Atex Zone 2 for indoor installation. They are air cooled and equipped with medium filtration, bleed valve for depressurization to vent, mechanic by-pass valve and controlled by electrical board S1-20.
View more

Model UVG 90

Italy

Screw biogas compressor for CO2 destined for the Italian market. Designed for installation in safe area outdoors. It is air-cooled and equipped with heat recovery, temperature control, fine filtration and controlled by PLC. The compressor uses food-grade oil.
View more

Model BVG 110

USA

Screw compressor for biogas upgrading destinated for US market. Designed in compliance with ASME and UL standards (Class 1 Division 2), for outdoor installation. It is air cooled and including fine filtration, electropneumatic by-pass valve and controlled by PLC.
View more

Model BVG 200

Colombia

Screw compressor for biogas upgrading located in Colombia. Designed for indoor installation, it is water cooled and completed with temperature control, electropneumatic by-pass valve and controlled by PLC.
View more

Model ADI115-30

Poland

Single-stage reciprocating compressor for natural gas installed in Poland. Designed for classified Atex Zone 2. It is air cooled and completed with fine filtration and electropneumatic by-pass valve. The electrical cabinet is designed for outdoor installation and controlled by PLC.
View more

Contact us

Write us for support or information