BIOGAS COMPRESSORS / RNG GRID INJECTION

UVG315/ VG250

2x UVG 315  

LOCATION: SPAIN
FLUID: Biogas    
POWER INSTALLED:
 400 kW (x2)
INLET PRESSURE: 50 mbar(g)
WORKING PRESSURE: Up to 15 bar(g)
FLOW RATE: 0<1850<3700 Nm³/h
AMBIENT TEMPERATURE: -10/+40°C

VG 250

LOCATION: SPAIN
FLUID: Biomethane  
POWER INSTALLED:
 315 kW
INLET PRESSURE: 50 mbar(g)
WORKING PRESSURE: Up to 22.5 bar(g)
FLOW RATE: 0<530<1045 Nm³/h
AMBIENT TEMPERATURE: -10/+40°C

 

A complete automatic solution for biogas upgrading and biomethane grid injection consisting of:
– Two open frame screw compressors for biogas upgrading installed inside a container (40’) in Spain for a total flowrate of 3800 Nm3/h. Designed in compliance with the European standards for classified Atex zone 2. It is suitable for outdoor installation, water-cooled, outlet gas temperature control, fine filtration and controlled remote by PLC;
– One screw compressor for biomethane grid injection, in compliance with the Spain requirements for the biomethane grid injection. Designed for classified Atex Zone 2 for outdoor installation, water-cooled, outlet gas temperature control, fine filtration, equipped with silencers for reducing the noise level to 75 dB(A) at 1 meter and controlled remote by PLC.

[contact_form]

OTHER REFERENCES

Model UVG315/VG250

Spain

Two screw compressors for biogas upgrading installed inside a container (40’) for a total flowrate of 3800 Nm3/h. One screw compressor for biomethane grid injection, in compliance with the Spain requirements for the GRFD. They are designed in compliance with the European standards for classified Atex zone 2, water-cooled, with outlet gas temperature control, fine filtration and remote control by PLC.
View more

Model ADLR9-45

Turkey

Two of five three stages reciprocating compressors for wellhead gas. Engineered with gas engine and local control panel equipped with PLC and suitable for classified area zone 2. Designed for outdoor installation and with by-pass valve for flow rate regulation.
View more

Model UVG 90

France

Screw biogas compressor for upgrading located in France. Designed for classified Atex Zone 2 for outdoor installation, air-cooled, completed with temperature control, heat recovery and controlled by PLC. It is equipped with fully electrical by-pass system.
View more

Model UVG315

Italy

Screw biogas compressor for upgrading located in Italy. Designed for classified Atex Zone 2 for indoor installation, water-cooled, completed with temperature control, fine filtration and controlled by PLC.
View more

Model UVG355

Netherlands

Screw biogas compressor for upgrading located in the Netherlands. Designed for classified Atex Zone 2 for indoor installation, air-cooled, completed with temperature control, heat recovery and controlled by PLC.
View more

Model UVG110

France

Screw biogas compressor for upgrading located in France. Designed for classified Atex Zone 2 for outdoor installation, air-cooled, completed with temperature control, heat recovery and controlled by PLC. It is equipped with electro-pneumatic by-pass system.
View more

Model UVG110

France

Screw biogas compressor for upgrading located in France. Designed for classified Atex Zone 2 for indoor installation, air-cooled, completed with heat recovery, temperature control and controlled by PLC. It is equipped with mechanical oil shaft seal & pressurized suction condensate drainer.
View more

Model UVG110

Swiss

Screw biogas compressor for upgrading located in Swiss. Designed for classified Atex Zone 2 for indoor installation, water-cooled, completed with activated carbon column, temperature control, fine filtration and controlled by PLC.
View more

Model UVG 200

USA

Screw biogas compressor for upgrading located in USA. Designed in compliance with north american standards, suitable for outdoor installation, air-cooled, completed with electro-pneumatic by-pass system and controlled by PLC.
View more

Model BVG45

Turkey

Screw biogas compressor for upgrading located in Turkey. Designed for classified Atex Zone 2 for outdoor installation, air-cooled, completed with electro-pneumatic by-pass valve, heat recovery and controlled by PLC.
View more

Contact us

Write us for support or information